StyroGoo Foam GlueGlue foam to almost anything!Free Shipping in the USA Only!International orders will be charged shipping after checkout! International customers should order from the main page here and select 8.5oz under the size dropdown.Powerful instant-tack foam safe glue for EPS and XPS. For all your craft and hobby needs. Ideal for permanently adhering foam, foam rubber, paper, glass, fabric, wood, plastic, metal and cardboard. To see a comparison of all our glues and adhesives, click here To see foam projects made using this product, click here. Features:
Used For:
To see foam projects made using this product, click here
Instructions:Clean the areas to be glued. Apply a thin layer to one or both surface. Press the two pieces together. Allow to dry for 30 minutes. Full adhesion in 12 hrs. Precautions: Keep container closed. Use in ventilated areas as it contains toxic and flammable substances. This product should be used under adult supervision. If swallowed, induce vomiting. In case of contact with eyes rinse with water for 15 minutes and consult physician. Keep off skin. Avoid breathing vapor. Wash hands thoroughly after handling. Store in a cool place. Contains polyvinyl acetate and solvents. Flammable.
Additional Info:California Proposition 65 Warning: This product contains a chemical known to the State of California to cause cancer, birth defects, and reproductive harm. While applying use a dust mask or respirator with an RPE of 20 or 40. For more information, go to www.P65Warnings.ca.gov or HWFF's information page: California Proposition 65. WARRANTY: HWFF Inc./dba Hot Wire Foam Factory warrants this product to be of merchantable quality when used or applied in accordance with the instructions herein. The product is not warranted as suitable for any purpose or use other than the general purpose for which it is intended. Liability under this warranty is limited to the replacement of its product (as purchased) found to be defective, or at the shipping companies’ option, to refund the purchase price. In the event of a claim under this warranty, notice must be given to The Hot Wire Foam Factory in writing. This limited warranty is issued and accepted in lieu of all other express warranties and expressly excludes liability for consequential damages. MSDS available on request.
Videos:
|
I am interested in your StyroGoo for a project involving expanded polystyrene (EPS). I want to be certain that StyroGoo will not dissolve or otherwise cause damage to the EPS. Can you provide confirmation?
Styrogoo is made specifically for EPS (the white beaded foam) and XPS (like our Art & Sign Foam, Dow Blueboard, and Owens-Corning pink Foamular, and Styrofoam), and it will not dissolve them. We have been using StyroGoo ourselves and have sold thousands of bottles over the past several years with no reports of any harm whatsoever to EPS foam.
You are wise to be cautious, I used some Liquid Nails Foam Safe Glue about 12 years ago. I tested it and in two weeks all was fine. I then glued about 200 feet of foam molding to a building and almost a year later the foam started falling off. Upon inspection I found that the glue had dissolved the foam. There must have been some slow acting solvents that acted on the foam over time.
I did a sample glue joint last night on EPP and it appears to be taking a long time to dry. What's up?
EPP, expanded polypropylene, is a closed cell foam so it will take much longer for the glue to dry in the middle where no air gets to it. I think you will need something that has a solvent which dissolves polypropylene to get a 100% bond. The Styrogoo will stick like crazy to just about anything, but it won't chemically bond to the type of foam you are using. I have used Styrogoo to glue closed cell polyethylene and it sticks really well, but I could tear it apart, and had to wait twice as long for it to dry. Applying a thin layer of glue to each side helps it dry faster.
When you glue Styrofaom, EPS or XPS which are open cell foams, with Styrogoo the foam will tear before the glue lets go.
What is the difference between your foam glues?
Here is a brief comparison of all of our glues. We really like Foam Fusion because it is nontoxic, but it takes more patience.
- foam-safe
- non-toxic
- sets up in 30-60 minutes
- dries overnight (longer with XPS foam)
- can only be use on porous materials
- must be put on very thin, so best for flat sheets of foam
- the most economical foam glue
- can be cut through with hot wire tools, but slows the cut down
- foam-safe
- toxic and flammable while setting up
- sets up in minutes
- dries in 3-6 hours (longer with XPS foam)
- can be used on porous materials, plus glass, plastic, metal, painted surfaces, etc.
- has body to it, so can be used on uneven surfaces
- can be cut through with hot wire tools, but slows the cut down a little more than with Foam Fusion
- Foam-safe
- Allow 3 minutes before joining, then instant tack
- Dries in 1 hour
- can be used on porous materials, plus glass, plastic metal, painted surfaces, etc.
- must be put on somewhat thin, so best for flat sheets of foam
- can be cut through with hot wire tools, but slows the cut down a little more than with Foam Fusion
Boost added to powdered foam coats:
- foam safe
- non-toxic
- sets up in 30min with All Purpose and Create Coat, and 90min with Exterior Foam Coat
- dries 30-60min with All Purpose and Create Coat, and overnight with Exterior Foam Coat
- can be used on porous plus glass, metal, painted surfaces, etc (cannot even be chipped off metal with a hammer)
- has body to it, so can be used on uneven surfaces
- cannot be cut through with hot wire tools
